Shoreface profile

From Coastal Wiki
Revision as of 11:32, 21 September 2018 by Dronkers J (talk | contribs) (Created page with " {{Definition|title=Shoreface profile |definition= The shoreface profile, often called beach profile, is the cross-shore coastal depth profile extending from the low-water lin...")
(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)
Jump to: navigation, search
Definition of Shoreface profile:
The shoreface profile, often called beach profile, is the cross-shore coastal depth profile extending from the low-water line to the closure depth.
This is the common definition for Shoreface profile, other definitions can be discussed in the article


Introduction

File:ShorefaceProfile.jpg
Figure 1. Schematic representation of a shoreface profile. The vertical/horizontal scale ratio is greatly exaggerated.


Figure 2. The barred coast of North Holland, The Netherlands. https://beeldbank.rws.nl, Rijkswaterstaat / Rens Jacobs

The shoreface is the zone where offshore generated waves dissipate their energy, thereby suspending and transporting large quantities of sediment. Most energy is dissipated in the upper part of the shoreface, the surf zone, where waves overturn and break. The lower part of the shoreface extends to the so-called closure depth, the depth where the seabed is hardly influenced by waves and where wave-induced sediment transport is insignificant. The lower part of the shoreface is also called shoaling zone; wave shoaling is the process of wave amplification when waves travel from deep to shallow water before breaking. The division between upper and lower shoreface profiles is generally marked by an inflexion point, a bar or a terrace, indicating transition of morphodynamics [1] (Fig. 1). Another transition exists at the shoreline where waves collapse and run up the beach, the so-called swash zone. The surf zone profile is often undulated due to the presence of one or several bars. These bars have mainly a shore parallel orientation, but more complex three-dimensional patterns are ubiquitous (see Rhythmic shoreline features and Fig. 2).


Morphodynamic feedback

Sediment transport on the shoreface depends on the local wave climate. The wave climate is the description of incoming waves in terms of a statistical distribution of incident wave directions, wave heights and wave periods. Sediment transport also depends on the characteristics of bed sediments and on the seabed bathymetry. For small wave incidence angles (close to the shore-normal direction) the relevant seabed bathymetry is the shoreface profile.

The shoreface profile influences cross-shore sediment transport, but the inverse also holds: changes of the shoreface profile result from gradients in the cross-shore sediment transport. There is morphodynamic feedback: for a given incident wave field the shoreface profile determines the transformation of the wave field on the shoreface and therefore the resulting sediment transport, whereas the resulting sediment transport determines the shoreface profile. As a result of this morphodynamic feedback, the shoreface profile tends to an equilibrium shape for a given stable wave climate. A dynamic equilibrium is reached when onshore directed sediment transport and offshore directed transport are equal on average over a period exceeding the morphodynamic adaptation time. This holds for alongshore uniform coasts; the equilibrium requirement for non-uniform coasts is a vanishing divergence of the long-term average total sediment transport vector (cross-shore and alongshore). It was realised already long ago that the shoreface of a sedimentary coast should not be regarded as a geologically inherited feature, but as the result of natural adaptation to modern hydrodynamic conditions. [2] [3].

Determination of the equilibrium shoreface profile has great practical interest. It provides quantitative insight in the response of the shoreface to changes in the local wave climate by human and natural causes; such insight is important for testing and improving the effectiveness of measures to combat coastal erosion and shoreline retreat.


Bedforms and sediment sorting

Morphodynamic feedback involves not only shoreface profile development, but also sediment grainsize and bed roughness. Grainsize and bed roughness strongly influence sediment transport [4]. Inversely, sediment transport strongly influences the grainsize distribution of bed sediments. Bed roughness depends on the presence of bedforms (ripples, dunes), which in turn depend on sediment transport and sediment grainsize. Consequently, shoreface profile development, wave transformation on the shoreface, sediment transport, grainsize sorting and bedform emergence are all dynamically coupled processes.

Grainsize sorting is primarily due to differences in transport modes of different grainsize fractions. The finer fractions are more easily brought and maintained in suspension than the coarser fractions. They are transported further away from their initial location and tend to settle on the lower shoreface zone where wave-induced bed shear stresses are lower than on the upper shoreface. The coarse fraction is transported partly as suspended load and partly as bedload in the wave boundary layer; skewed shallow-water waves favour net onshore transport in the wave boundary layer. Sediments on the upper shoreface are therefore coarser than on the lower shoreface. Fine sediment particles can still be present on the upper shoreface, but they are hidden by overlying coarser sediment particles – a phenomenon called 'bed armouring'.

The largest bedforms on the shoreface, such as shoreface-connected ridges (scale of several kilometers) and shore-oblique bars (scale of the order of hundred meters) are mainly related to longshore transport through morfodynamic feedback processes, see the articles Sand ridges in shelf seas and Rhythmic shoreline features. Other large bedforms, the so-called breaker bars (scale also of the order of 100 meters) arise from morphodynamic coupling with the wave breaking process, through the resulting flow structure at the breaker bar [5][6]. Bedforms at much smaller scales – ripples with wavelengths of the order of 1 m – are formed in the less exposed parts of the shoreface under low to moderate wave conditions. Morphodynamic feedback processes, leading to regular ripple patterns, involve ripple-induced near-bed flow circulation [7], vortex shedding at ripple crests [8] and non-linear ripple-ripple interactions [9]. For a more detailed explanation, see the articles Wave ripples and Wave ripple formation. The time lag of sediment suspension and settling related to vortex shedding at the ripple crests strongly influences the direction of residual sediment transport on the shoreface.


Beach classification

The beach profile in the upper shoreface zone can be highly variable. The profile tends to steepen in periods of low-energy waves (especially long-period swell waves) and to flatten under high-energy storm waves. Sediment characteristics also play an important role. Coarse-grained beaches, typical for high-energy coasts, have steeper slopes than fine-grained beaches, typical for moderate-to-low-energy coasts. Gently sloping beaches dissipate almost completely the energy of incident waves, whereas steep sloping beaches tend to reflect incident waves, at least partly. For distinguishing between reflective and dissipative beaches the Dean-parameter [math]\Omega[/math] is often used [10][11]:

[math]\Omega = \Large \frac{H}{wT} \normalsize , \qquad(1)[/math]

where [math]H[/math] is the wave height before breaking, [math]T[/math] is the peak spectral wave period and [math]w[/math] is the sediment fall velocity. By analysing beach profiles in Australia, Wright and Short (1984) [12] found that beach types could be characterised by the parameter [math]\Omega[/math]:

  • reflective beaches correspond to [math]\Omega \lt 1 [/math];
  • intermediate beaches correspond to [math]1\lt \Omega \lt 6 [/math];
  • dissipative beaches correspond to [math]\Omega \gt 6 [/math].

The tidal range also influences the beach profile, because the breaker zone is shifted along the shoreface with tidal level. For large tides (tidal range much larger than wave height) the surf zone covers during the tidal cycle a much larger area than for small tides. Beaches with large tides therefore have smaller upper shoreface slopes compared to beaches with the same [math]\Omega[/math] and small tides.


Cross-shore sediment transport

Sediment transport on the shoreface depends on many processes. We focus on processes relevant for cross-shore transport. It should be realised, however, that longshore transport processes can also play an important role. Shifts in the cross-shore position of the shoreface profile and the generation of bars on the shoreface are strongly influenced by longshore transport processes. See for example the articles: Natural causes of coastal erosion, Littoral drift and shoreline modelling and Rhythmic shoreline features. In the following we focus on sandy beaches, with grain sizes typically between 0.2 and 0.5 mm (fine to medium sand). Coarse sedimentary beaches are dealt with in the article Gravel Beaches.

Onshore wave-induced sediment transport

Wave transformation in shallow water (see Shallow-water wave theory) is a major factor for onshore sediment transport [13]. Waves become asymmetric and skewed, producing near-bed sheer stresses which are stronger in forward (onshore) direction than in backward (offshore) direction [14] [15][16]. Phase lags between bed sheer stress and sediment suspension determine to which degree wave skewness induces onshore transport; in some situations (rippled bed, sheet flow) a large phase lag can even reverse the net sediment transport direction [17][18][19]. The development of forward streaming at the top of the wave boundary layer also contributes to onshore transport [20], but this only holds for smooth beds and not in cases where the seabed is rippled, in cases of strongly skewed waves or for sheet flow conditions [21][22]. A lesser contribution to onshore transport is further due to net mass transport in the zone between wave trough and wave crest.

Offshore wave-induced sediment transport

Offshore transport is due to so-called undertow: the compensating return current for the net onshore mass transport in the zone between wave trough and wave crest [23]. The undertow current is particularly strong just in front of the location where waves are breaking and where much sediment is brought into suspension[24]. Bound infragravity waves may also contribute to net offshore sediment transport, as discussed in the article Infragravity waves.

Downslope sediment transport

Downslope transport occurs when sediment particles roll down the shoreface slope. However, this is not the primary cause of downslope sediment transport for fine to medium sandy beaches [25]. Sediment transport by downrolling is a minor effect for two reasons: (1) the shoreface slope is small and (2) sediment particles move (much) more by transport in suspension than by bedload, especially on the upper shoreface. When a sediment particle is lifted from the bed to a certain level [math]z[/math] into the fluid, it moves with the wave orbital flow over a net distance [math]l[/math] until settling again onto the bed. The net distance [math]l[/math] travelled by the sediment particle depends on the settling time; the longer the settling time, the greater the distance. The settling time is inversely proportional to the sediment fall velocity [math]w[/math]. Because the shoreface has a seaward dipping slope, the net travelled distance by an offshore moving sediment particle is larger than for a flat bottom; the inverse holds for an onshore moving sediment particle. The slope effect thus requires a correction to the net sediment transport over a flat bottom, which depends on the slope [math]\beta[/math] and the fall velocity [math]w[/math]. Sediment transport models assume in general that the slope effect can be represented by a correction factor to the wave-induced transport components of the form [26]

[math](1-\gamma \Large \frac{\beta u }{w} \normalsize ) , \qquad(2)[/math]

where [math]\beta[/math] is the bed slope, [math]u[/math] the wave orbital velocity, [math]w[/math] the sediment fall velocity and [math]\gamma[/math] an efficiency parameter. Although not proven, it is often assumed that the slope effect is the primary factor compensating for net wave-induced onshore transport in situations close to equilibrium. This implies that the equilibrium shoreface slope [math]\beta[/math] will be steeper (larger [math]\beta[/math]) for a coarser seabed (larger fall velocity [math]w[/math]) than for a finer sediment bed (smaller fall velocity [math]w[/math], smaller [math]\beta[/math]), according to the expression (2) for the correction factor. This is in general agreement with field observations.

Sediment transport modelling

The processes involved in sediment transport on the shoreface, as described above, are very complex and not yet fully understood. Even the most sophisticated process-based mathematical models, like XBEACH [27], make use of approximate empirical formulations for several processes contributing to sediment transport and involve parameters that need to be tuned. Empirical formulas for wave-induced sediment transport on the shoreface that are often used in practice are given in Sediment transport formulas for the coastal environment and Sand transport. These formulas are based on laboratory and field measurements for a large range of conditions. Rough estimates can be obtained with the empirical default parameters given in these articles. For better estimates it is necessary to tune these parameters to field data.


Equilibrium shoreface profile

For a given stable wave climate the shoreface profile tends after a long period to an equilibrium profile. This equilibrium profile can be computed by applying sediment transport formulas to an initial profile for a period comprising all wave conditions according to local wave climate statistics. As this requires tedious computations and produces results with large uncertainty margins, equilibrium profiles derived from field observations are more often used. From analysis of a large number of beach profiles of the Californian and Danish coasts [28][29] and the US Atlantic and Gulf coasts [30] Bruun (1954) and Dean (1977) derived an equilibrium profile of the form (Fig. 3)

Figure 3. The Bruun/Dean profile (Eq. 3) and the equivalent Bodge profile (Eq. 4).

[math]h(x)=A \; x^{2/3}, \qquad(3)[/math]

where [math]h[/math] is the water depth [m], [math]x[/math] the cross-shore distance [m] ([math]x=0[/math] at the shoreline) and [math]A [/math] a coefficient depending on the sediment fall velocity [math]w[/math] [m/s], [math] \quad A \approx 0.5 \; w^{0.44} [m^{1/3}][/math].

Dean [30] showed that the exponent 2/3 is consistent with the assumption of constant wave energy dissipation per unit volume throughout the surf zone.

Because the Bruun/Dean profile has an infinite slope at the shoreline, an alternative form was proposed by Bodge (1992) [31],

[math]h(x)=B \; (1 – e^{-kx}) , \qquad(4)[/math]

where [math]k[/math] is an empirical coefficient in the range [math]3 \; 10^{-5} - 1.16 \; 10^{-3} \; [m^{-1}][/math].

From an analysis of terrace-shaped shoreface profiles in northern Spain, Bernabeu et al. (2003) [32] found that the Bruun/Dean profile was adequate only for the upper shoreface; for the lower shoreface they proposed the form

[math]h(x)=A' \; (x-x_0)^{2/3} , \qquad(5)[/math]

where [math]x_0[/math] is determined such that the two profiles (3) and (5) match at the inflexion point between the upper and lower shoreface.

Inman et al. (1993) [33] used a similar procedure for the analysis of beach profiles for the coasts of south California, North Carolina and the Nile delta. They found best fits with exponents ranging between 0.3 and 0.45 instead of 2/3.


Analytical equilibrium models

Because of the earlier mentioned difficulties to derive model estimates of the equilibrium shoreface profile taking into account the full wave climate, analytical models have been developed in which the wave climate is replaced by a single representative monochromatic incident wave. An alongshore uniform shoreface is assumed with perpendicular wave incidence. A simple wave transformation model is used based on depth saturation of broken waves and shallow-water wave theory (see Shallow-water wave theory). An analytical expression for the equilibrium shoreface slope can be derived by requiring that the total wave-integrated cross-shore sediment flux equals zero throughout the shoreface zone [34] [25] [35]. Although these models yield certain properties also observed in the field, such as increasing profile steepness with increasing grain size and with increasing wave period, a more detailed comparison of computed profiles with observations exhibits large discrepancies. The computed concavity of the upper shoreface profile is much stronger than generally observed in the field and much stronger than for the Bruun/Dean profile. This is perhaps not surprising in view of the simplicity of the model for wave-induced sediment transport, which ignores many of the processes described in the previous paragraphs. The model also ignores the influence of major storms, which flatten the profile out to great depths. The profile adaptation time scale for the entire shoreface being quite long (order of centuries [25]), it is plausible that observed shoreface profiles often correspond to transient profiles [35].


Related articles

Bruun rule

Active coastal zone

Definitions of coastal terms



Further reading

Komar, P.D. 1998. Beach processes and sedimentation. Prentice Hall, London, pp. 544.

Woodroffe, C.D. 2002. Coasts, form, processes and evolution. Cambridge Univ.Press, 623 pp.

Dronkers, J. 2017. Dynamics of Coastal Systems. World Scientific Publ. Co. 753 pp.


References

  1. ↑ Wright, L.D., Chappel, J., Thom, B.G., Bradshow, M.P. and Cowell, P. 1979. Morphodynamics of reflective and dissipative beach and inshore systems: south-eastern Australia. Mar.Geol. 32: 105-140
  2. ↑ Cornaglia, P. 1889. Delle Spiaggie. Accademia Nazionale dei Lincei, Atti.Cl.Sci.Fis., Mat.e Nat.Mem. 5: 284-304
  3. ↑ Johnson, D.W. 1919. Shore processes and shoreline development. Prentice Hall, N-Y, 584 pp.
  4. ↑ Van Rijn, L.C. 1998. Principles of Coastal Morphology. Aqua Publications, The Netherlands (aqua publications.nl.
  5. ↑ Reniers, A.J.H.M., Thornton, E.B., Stanton, T.P. and Roelvink, J.A. 2004. Vertical flow structure during Sandy Duck: observations and modelling. Coast.Eng. 51: 237-260
  6. ↑ Jacobsen, N.G. and Fredsoe, J. 2014. Formation and development of a breaker bar under regular waves. Part 2: Sediment transport and morphology. Coastal Eng. 88: 55-68
  7. ↑ Sleath, J.F.A. 1984. Sea bed mechanics. Wiley, New York.
  8. ↑ Fredsøe, J., Andersen, K.H. and Sumer, M.B. 1999. Wave plus current over a ripple-covered bed. Coastal Eng. 38: 177-221
  9. ↑ Marieu, V., Bonneton, P., Foster, D.L. and Ardhuin, F. 2008. Modeling of vortex ripple morphodynamics. J. Geophys. Res. 113, C09007, doi:10.1029/2007JC004659
  10. ↑ Gourlay, M. R. 1968. Beach and dune erosion tests. Rep. m935/m936, Delft Hydraul. Lab., Delft
  11. ↑ Dean, R.G. 1973. Heuristic models of sand transport in the surf zone. Proc. Conf. Eng. Dynamics in the Surf Zone, Sydney: 208-214.
  12. ↑ Wright, L.D. and Short, A.D. 1984. Morphodynamic variability of surf zones and beaches: a synthesis. Mar.Geol. 56: 93-118
  13. ↑ Elgar, S., Gallagher, E.L. and Guza, R.T. 2001.Nearshore sandbar migration. J.Geophys.Res. 106: 11,623-11,727
  14. ↑ Nielsen, P. 1992. Coastal bottom boundary layers and sediment transport. In: Advanced Series on Ocean Engineering, IV. World Scientific.
  15. ↑ Abreu, T., Silva, P.A., Sancho, F. and Temperville, A. 2010. Analytical approximate wave form for asymmetric waves. Coastal Eng. 57: 656-667
  16. ↑ Van der A, D.A., O’Donoghue, T., Davies, A.G. and Ribberink, J.S. 2011. Experimental study of the turbulent boundary layer in acceleration-skewed oscillatory flow. J. of Fluid Mech. 684: 251-283
  17. ↑ Vincent, C.E. and Green. M.O. 1990. Field measurements of the suspended sand concentration profiles and fluxes and of the resuspensionm coefficient over a rippled bed. J.Geophys.Res. 95: 11591-11601
  18. ↑ Ribberink, J.S. and Al-Salem, A.A. 1995. Sheet flow and suspension of sand in oscillatory boundary layer. Coastal Eng. 25: 205-225
  19. ↑ Ruessink, B.G., Michallet, H., Abreu, T., Sancho, F., van der A, D.A., van der Werf, J.J. and Silva, P.A., 2011. Observations of velocities, sand concentrations, and fluxes under velocity-asymmetric oscillatory flows. J. Geophys. Res. 116, C03004, doi:10.1029/2010JC006443
  20. ↑ Longuet-Higgins, M.S. 1953. Mass transport in water waves. Royal Soc. London, Phil.Trans. 245A: 535-581
  21. ↑ Trowbridge, J.H. and Madsen, O.S. 1984. Turbulent wave boundary layers: 2. Second-order theory and mass transport. J.Geophys.Res. 89: 7999-8007
  22. ↑ Kranenburg, W. M., Ribberink, J. S., Uittenbogaard, R. E. and Hulscher, S. J. M. H. 2012. Net currents in the wave bottom boundary layer: on wave shape streaming and progressive wave streaming. J. Geophys. Res. 117(F03005), doi:10.1029/2011JF002070
  23. ↑ Cox, D.T. and Kobayashi, N. 1998. Application of an undertow model to irregular waves on plane and barred beaches. J.Coast.Res. 14: 1314-1324
  24. ↑ Reniers, A.J.H.M., Thornton, E.B., Stanton, T.P. and Roelvink, J.A. 2004. Vertical flow structure during Sandy Duck: observations and modelling. Coast.Eng. 51: 237-260
  25. ↑ 25.0 25.1 25.2 Stive, M. J. F. and de Vriend, H. J. 1995. Modelling shoreface profile evolution. Marine Geology 126: 235–248
  26. ↑ Bagnold, R.A. 1963. Mechanics of marine sedimentation. In: The sea, vol.3. Ed. M.N.Hill, Wiley-Interscience: 507-528
  27. ↑ https://oss.deltares.nl/web/xbeach/home
  28. ↑ Bruun, P. 1954. Coast erosion and the development of beach profiles. Beach Erosion Board, US Army Corps of Eng., Tech.Mem. 44: 1-79
  29. ↑ Dean, R.G. 1977. Equilibrium beach profiles: US Atlantic coast and Gulf coasts. Ocean Eng.Tech.Rep. 12, Univ. of Delaware, Newark, 45 pp .
  30. ↑ 30.0 30.1 Dean, R.G. 1977. Equilibrium beach profiles: US Atlantic coast and Gulf coasts. Ocean Eng.Tech.Rep. 12, Univ. of Delaware, Newark, 45 pp.
  31. ↑ Bodge, K.R. 1992. Representing equilibrium beach profiles with an exponential expression. J. Coastal Research 8: 47-55.
  32. ↑ Bernabeu, A.M., Medina, R. and Vidal, C. 2003. A morphological model of the beach profile integrating wave and tidal influences. Mar.Geol. 197: 95-116
  33. ↑ Inman, D.L., Elwany, M.H. and Jenkins, S.A. 1993. Shorerise and bar-berm profiles on ocean beaches. J.Geophy.Res. 98: 18181-18199
  34. ↑ Bowen, A.J. 1980. Simple models of nearshore sedimentation; beach profiles and longshore bars. In: The coastline of Canada, Ed. by S.B. McCann, Geological Survey of Canada, Ottawa, pp. 1-11
  35. ↑ 35.0 35.1 Ortiz, A.C. and Ashton, A.D. 2016. Exploring shoreface dynamics and a mechanistic explanation for a morphodynamic depth of closure. J. Geophys. Res. Earth Surf 121: 442–464 doi:10.1002/2015JF003699


The main author of this article is Job Dronkers
Please note that others may also have edited the contents of this article.
Citation: Job Dronkers (2018): Shoreface profile. Available from http://www.coastalwiki.org/wiki/Shoreface_profile [accessed on 21-11-2024]
Retrieved from "https://www.coastalwiki.org/w/index.php?title=Shoreface_profile&oldid=73523"