Difference between revisions of "Testpage4"

Revision as of 21:39, 5 April 2020

Groundwater management in low-elevation coastal zones

Groundwater is an important resource for drinking water and irrigation. However, groundwater extraction in low-lying coastal zones is highly problematic. It raises the salinity of the groundwater and it makes the land sink. Therefore, groundwater management is a major issue in many low-lying coastal areas. This article focuses on shallow coastal aquifers connected to the sea.

Threats of groundwater extraction

Fig. 1. World water distribution. Source: pbslearningmedia ^[1].

Fig. 2. Agricultural groundwater usage for selected countries in [math]\small 10^9 \, km^3/year[/math]. Source: UN World Water Development Report, 2015^[2].

Fresh water represents only a small fraction of earth's water resource – less than 1%, ice excluded (Fig. 1). Groundwater is by far the most important fresh water resource available for human use. More than 50% of world’s population lives in coastal areas and is largely dependent on fresh groundwater resources for domestic, agricultural and industrial purposes. The exploitation of fresh groundwater resources is sharply increasing as a consequence of population growth, economic growth, intensified agricultural development, and the degradation of surface water resources due to contamination (Fig. 2).

Worldwide, many large coastal cities have expanded into low coastal plains during the past decades, especially in Asia and Africa (see Coastal cities and sea level rise). Most of these plains emerged after the Holocene marine transgression, when the seabed was raised above sea level by sedimentation behind a sheltering coastal barrier. These deposits form a top soil layer of a few meters up to several tens of meters thick, and contain a high fraction of fine sediments of fluvial and marine origin (and peat, in humid climatic zones). On these poorly draining soils, which are highly susceptible to compaction, extensive urban and industrial development has taken place^[3]. The land elevation is generally close to the mean high sea level. However, in many areas it is lower and still subsiding, mainly as a result of drainage and groundwater extraction^[4].

Intensive groundwater extraction from underlying water-bearing layers (aquifers) stimulates the intrusion of seawater, leading to increased groundwater salinity^[5]. In the lowest areas, brackish groundwater may reach the surface by upward groundwater flow through the confining top layer, so-called 'saline seepage'. The threats of uncontrolled groundwater extraction can remain unnoticed for many years because groundwater flow is a slow process. However, in the long run they are considerable ^[6]:

unsuitability of groundwater for drinking water,
reduced usability of groundwater for irrigation,
soil salinization detrimental to crop growth,
deterioration of the foundation of buildings by corrosion of concrete, reinforcement and bricks,
soil subsidence and increased vulnerability to flooding,
danger of collapse of buildings due to soil instability.

In addition, the anticipated sea level rise and the decrease of recharge, due to climate change and increased water demand in the upstream catchment areas, will further exacerbate the pressures on coastal groundwater systems.

Salt intrusion processes

Fig. 3. A small level difference is sufficient to keep a large fresh water column in balance with a salt water column.

Seawater intrudes into the underground of the coastal plain through aquifers, permeable soil layers consisting of medium / coarse granular material or porous / fissured rock. Due to its greater density, it enters like a wedge that pushes fresh water inshore, see Fig. 4. A counter-pressure is exerted by the inshore rising fresh water table. Due to the small density difference, a small elevation of the fresh water head is sufficient to keep the seawater intrusion in balance, see Fig. 3. In Fig. 4 it is assumed that the permeability of the underground is the same everywhere. In reality, however, this is never the case due to the presence of poorly permeable layers (aquitards); Fig. 5 shows a still much simplified but slightly more realistic image. A rough estimate of the intrusion length [math]L[/math] of the seawater wedge into a confined aquifer is given by ^[7]

[math]L \approx \alpha k D^2 / (2 Q) , \qquad (1)[/math]

where [math]\alpha \approx 1/40[/math] is the relative density difference, [math]k[/math] is the hydraulic conductivity, [math]D[/math] is the aquifer depth and [math]Q[/math] is the groundwater discharge.

Fig. 4. Schematic representation of seawater intrusion into a homogeneous coastal aquifer.

Fig. 5. Schematic representation of seawater intrusion into a multi-aquifer system.

Seawater intrusion depends, via the groundwater discharge [math]Q[/math], on the elevation difference between the inland fresh water table and the water level at sea. The sea level is variable due to tidal motion and wind set-up / set-down and the inland fresh water table varies over the seasons in response to variable fresh water runoff, evapotranspiration and extractions. These fluctuations in the groundwater pressure gradient, together with spatial inhomogeneities in the geologic structure, contribute to mixing across the fresh-salt interface ^[8]. Sea level rise is an ongoing trend that gradually increases the seawater intrusion into the underground. Shoreline retreat associated with sea level rise can also play a role. Seawater intrusion is further enhanced in case of a trend-wise decrease of the fresh groundwater flux to the coast.

Several other processes contribute to salinization of coastal aquifers.

Marine transgression.

Many coastal areas were flooded by the sea during the Holocene transgression, before sedimentation raised the seafloor above mean high water level and before fluvial processes became dominant. The present saline groundwater was largely formed during this period. Saline intrusion in coastal aquifers by marine transgression occurs today only under extreme storms. Such extreme conditions are rare, but they are expected to become much more frequent in future as a consequence of relative sea level rise (see Sea level rise). The process of seawater infiltration in a fresh aquifer resulting from a marine flood is shown in Fig. 6. Increased groundwater salinities persist several years after such flood events^[9].

Seawater intrusion via estuaries.

Coastal aquifers are not only in contact with salt water at the land-sea boundary but often also with salt water of estuaries. In this way, intrusion of saline surface water into shallow groundwater can take place further inland (Fig. 7). The intrusion of seawater in estuaries is discussed in the articles Seawater intrusion and mixing in estuaries and Estuarine circulation. Seawater intrusion in estuaries has strongly increased during the past century due to channel deepening (dredging) for navigational purposes. The greatest incursion of high salinity seawater occurs in periods of low fluvial runoff, especially in microtidal estuaries (see Salt wedge estuaries).

Fig. 6. Infiltration of marine flood water into the underground.

Fig. 7. Intrusion of seawater from a salt-wedge estuary into the underground.

Groundwater extraction.

Intensive groundwater extraction increases the intrusion of seawater into the coastal aquifer by diminishing the groundwater discharge to the sea (according to Eq. 1). This intrusion is a slow process, but with a long-lasting impact. The most immediate effect of pumping up groundwater is the rise of the fresh-salt transition under the well, a phenomenon called 'upconing', see Fig. 8. When a critical limit of the extraction rate is exceeded, the fresh-salt transition rises up to the well mouth and the pumped water becomes brackish. The rise of the fresh-salt transition is strongest in cases where the hydraulic conductivity [math]k[/math] of the aquifer is small (low conductivity limits the horizontal groundwater flow towards the well)^[10]. For aquifers with a low permeability (small [math]k[/math]), only small abstraction rates are possible.

Saline seepage.

In areas situated below sea level, groundwater can move upwards to the soil surface if the upper soil layer is semipermeable, see Fig. 9 and 10. The upward moving saline seepage water may (1) discharge directly in lakes, canals, ditches or subsurface drain tiles leading to the salinization of surface waters, (2) mix near the surface with shallow fresh groundwater, or even (3) reach the root zone affecting crop growth and natural vegetation. Where rainwater or fresh surface water supplies are limited, saline seepage leads to salinization of surface water and shallow groundwater - a process known as internal salinization. The seepage flow depends on the surface soil level and on the thickness and permeability of the top soil layer. Seepage flow is enhanced at places where ancient sandy deposits are close to the surface or where cracks exist in the top clay layer, giving rise to so-called 'boils' ^[11]. Seepage in deep polders is increased when the top soil is drained for agricultural purposes; compaction of clay and peat soils is another serious consequence of drainage. The effect of seepage on seawater intrusion is similar to the effect of groundwater extraction; it causes upconing of brackish groundwater and increases the intrusion of seawater into the coastal aquifer.

Fig. 8. Upconing brackish water under a pumping well.

Fig. 9. Groundwater seepage into a polder and associated rise of the salt-fresh interface.

Fig. 10. Drainage of a polder causing upconing of brackish water into the ditches.

Irrigation practices.

In arid coastal plains where the groundwater salinity is too high, crops must be irrigated with water that is supplied from elsewhere. Due to water scarcity, the infiltrated irrigation water is collected in special drains and re-used for irrigation. Such an irrigation system exists, for example, in the Nile Delta ^[12]. Because the irrigation water is mixed with brackish groundwater, re-use can cause, in combination with evapotranspiration, a net salt flux to the land surface.

Groundwater management

Fig. 11. Factors that influence the groundwater system. From Post (2018)^[9].

Groundwater management requires an integrated approach based on insight into the multiple factors that influence the groundwater system, see Fig. 11. This insight is usually fragmentary due to the complexity of the groundwater system. Groundwater flow models are crucial for estimating the influence of abstractions on the groundwater status, see section Groundwater modelling. Permits, metering of wells, quotas and water taxes are the legal instruments on which sustainable groundwater management can be based, together with obligations of monitoring and reporting. Polluting substances from point sources (industrial effluents, household sewage) and from diffuse sources (agricultural effluents containing pesticides, herbicides, fertilizers) are a major danger for groundwater contamination. Adequate environmental policy, agricultural policy, and spatial policy that tackle the pollution issue are prerequisite for sustainable groundwater management. The effectiveness of groundwater management can be increased by involving local stakeholders, due to the strong link between use and usability of the groundwater resource. Understanding and support from stakeholders makes it easier to enforce legal rules and provisions. Without support of stakeholders, enforcement is usually difficult to achieve ^[13].

Monitoring aquifers for protection against depletion and pollution is a technically demanding and costly exercise so that information about aquifers is often incomplete. The costs for setting up a monitoring network, collecting data regularly, processing, interpreting, and storing it in databases, including unified databases at the national level, are one of the reasons why in developed and developing countries alike water rights and monitoring obligations, especially with respect to groundwater, may remain unimplemented ^[13].

Measures to reduce soil and groundwater salinization

Different types of measures are possible to reduce soil and groundwater salinization, which can be applied depending on the geological setting and the causes of salt intrusion.

1. Horizontal wells.

The risk of upconing of the salt-fresh interface can be reduced by 'skimming' the fresh water lens with a horizontal well, see Fig. 12. With this measure it is possible to exploit a brackish aquifer with a relatively thin fresh water lens. Periodically, natural (or artificial) recharge of the fresh water lens is necessary to get the salt-fresh interface back to its former position.

2. Fresh water storage by infiltration.

According to the principle shown in Fig. 3, a large fresh water reservoir can be created in the subsoil by raising the fresh water table. This principle can be applied in coastal zones protected by a dune belt. By infiltrating fresh water in the dunes – rain water or fresh water from other sources – the fresh water table can be raised such that a large column of fresh water in the subsoil is kept in hydrostatic balance with the seawater, due to the different densities (Fig. 13). If present, any protruding thick sandy deposit in the coastal zone (e.g., relic channel bars) can serve for fresh water storage in a similar way. Dune infiltration is widely used in the Netherlands to provide drinking water to coastal cities (e.g., Amsterdam, The Hague).

Fig. 12. Horizontal skimming well. The upconing effect is limited by spreading the extraction over a broad zone.

Fig. 13. Large fresh water reservoir created by dune infiltration.

3. Fresh water storage by injection.

Collected rainwater – or fresh water from other sources – can temporarily be stored in the subsoil for later re-use. Fresh water is injected into the deeper part of the aquifer and collected later from a higher pumping well, as shown in Fig. 14. A larger volume of fresh water can be stored by lowering the salt-fresh interface. Salt groundwater is pumped away from greater depth to reduce the hydrostatic pressure on the surface layer. This will prevent an existing freshwater lens from being pushed out^[14]. The brackish/salt water has to be discharged to the sea or it can be treated in a desalination plant for re-use^[15]. The extraction-injection is adjusted by a so-called automatic 'freshmaker system'^[14]. The principle is shown schematically in Fig. 15. Another option (if technically and economically feasible) is to pump the brackish/salt water through the underlying aquitard to a lower aquifer ('freshkeeper system'^[14]), see Fig. 16.

Fig. 14. Temporary storage of rainwater.

Fig. 15. Principle of the freshmaker system: withdrawal of brackish groundwater to make room for a thick fresh water lens.

Fig. 16. Principle of the freshkeeper system: removal of brackish groundwater to a lower aquifer to make room for storage of fresh water.

4. Aquifer barriers to prevent seawater intrusion.

Two types of barriers have been implemented in practice: hydraulic barriers and physical barriers. The usual principle of a hydraulic barrier is shown in Fig. 17. Fresh water (for example, purified sewage water) is injected into the aquifer close to the seaward boundary to create a pressure head that prevents the intrusion of seawater. Further inland, freshwater can be extracted (to a limited extent) in periods of drought from the fresh aquifer. A practical example is the hydraulic barrier installed in California near Los Angeles ^[16]. The effectiveness of this solution depends on the availability of fresh water during sufficiently long and frequent periods. Another principle is based on extraction of intruding seawater, as shown in Fig. 18. Drawbacks of this principle are the disposal of the extracted saline or brackish groundwater and the lowering of the piezometric heads, especially in shallow coastal aquifers^[17]. This latter issue can be mitigated by fresh water injection further landward^[18]. Physical subsurface barriers have been constructed in several countries, especially in Japan^[19] and China ^[20]. The barriers were generally built of concrete using grouting techniques or mixed-in-place slurry-wall methods^[21]. The dams serve as a barrier for seawater intrusion, and also create underground fresh water storage in periods of high precipitation (Fig. 19). However, the costs are high and the solution is only applicable in shallow aquifers^[17].

Fig. 17. Hydraulic injection barrier at the seaward entrance of an aquifer. The marine salt wedge is expelled in periods of abundant fresh water. Inland abstraction wells are exploited in periods of drought.

Fig. 18. Hydraulic abstraction barrier at the seaward entrance of an aquifer. The marine salt wedge is expelled in periods of abundant fresh water. Inland abstraction wells are exploited in periods of drought.

Fig. 19. Physical subsurface barrier at the seaward entrance of an aquifer.

5. Isolating saline areas.

Saline seepage due to local boils – a major salinization mechanism in the deep polders in the Netherlands – is combated by building a bypass around the saline areas. Automatic weirs control the temporary isolation (during dry periods) of saline areas with a significant number of boils. The temporarily stored salt water is discharged during rainstorm events when salt concentrations are low. Boils that arise from the removal of structures, such as level filters or sheet piles, or from the sealing of old gas wells, can be sealed. This can be done through injection of expanding and persisting fluids or through biosealing; the latter option is the most environmentally friendly.

Dealing with brackish groundwater

In arid coastal zones with endemic freshwater shortages, there are no good options for preventing salt intrusion into the groundwater. Strict regulation of groundwater abstraction is necessary to make land use possible. Agriculture has to make use of salt-tolerant crops. Fortunately, ever better crops are being developed for saline conditions, including by genetic modification techniques^[22]^[23]. In addition, infrastructure must be protected against corrosion by saline groundwater, including the use of salt-resistant concrete.

Groundwater modelling and observation

Fig. 20. SkyTEM team recording Time Domain Electromagnetic Data. Source: G. Oude Essink, https://publicwiki.deltares.nl/

Groundwater flow can be described with Darcy's law, which couples the flow rate linearly to the gradient in the hydrostatic groundwater pressure. A crucial problem is the determination of the coupling coefficient, the so-called hydraulic conductivity. This coefficient is different for each soil type. The structure and composition of the substrate is generally very complex. It is a reflection of the geological history in which a large number of processes on very diverse space and time scales play a role. The reliability with which groundwater flows can be simulated therefore depends primarily on the extent to which the structure and composition of the subsoil are known. This knowledge usually has large gaps, since sampling the subsurface over great depth requires a great deal of effort and is very expensive. In addition to knowledge of the subsurface structure, knowledge is needed of the distribution of saline water in the underground. Missing knowledge can be partially overcome by model calibration based on data from wells (quantity and quality of abstractions), piezometric surveys (groundwater pressure) and observations based on geophysical techniques.

In recent decades, a large number of geophysical measurement methods have been developed that indirectly provide information about the structure and properties of the subsurface and groundwater ^[24]. These are in particular: Seismic techniques, such as Ground Penetrating Radar (GPR ^[25]^[26]); Nuclear Magnetic techniques, such as Magnetic Resonance Sounding (MRS ^[27]), Time Lapse Gravity (TLG ^[28]); Electromagnetic techniques ^[29], such as Time Domain Electromagnetic sounding (TDEM ^[30]) and Induced Polarization (IP ^[31]). Most of these techniques can be applied on the ground or air-borne (Fig. 20). They provide indirect data on the structure of the subsurface and on the location of the salt-fresh transition, the groundwater flow, and salinity (by making use of the large electrical resistivity contrast between seawater and freshwater). Together with information from wells, bore holes and model calculations these data enable reasonable estimates of the effect of interventions in the groundwater system. However, the design of groundwater models and the interpretation of model results still require highly specialized knowledge and experience of geohydrological processes.

References

↑ pbslearningmedia https://www.pbslearningmedia.org/resource/buac17-35-sci-ess-waterdistribute/saltwater-and-freshwater-distribution-on-earth/
↑ WWAP (United Nations World Water Assessment Programme). 2015. The United Nations World Water Development Report 2015: Water for a Sustainable World. Paris, UNESCO https://unesdoc.unesco.org/ark:/48223/pf0000231823
↑ Jiao, J. and Post, V. 2019. Coastal Hydrogeology. Cambridge University Press.
↑ Syvitski, J. P., Kettner, A. J., Overeem, I., Hutton, E. W., Hannon, M. T., Brakenridge, G. R. and Nicholls R. J. 2009. Sinking deltas due to human activities. Nature Geoscience 2: 681-686
↑ Custodio, E. and Bruggeman, G.A., editors. Groundwater problems in coastal areas: a contribution to the International Hydrological Programme. Studies and reports in hydrology, vol. 45. Paris: UNESCO; 1987
↑ Post, V.E.A., Eichholz, M. and Brentführer R. 2018. Groundwater management in coastal zones. Bundesanstalt für Geowissenschaften und Rohstoffe (BGR). Hannover, Germany, 107 pp.
↑ Dagan, G. and Bear, J. 1968. Solving the problem of local interface upconing in a coastal aquifer by the method of small perturbations. Journal Hydraulogical Research 6: 15–44
↑ Werner, A.D., Bakker, M., Post, V.E.A., Vandenbohede, A., Lu, C., Ataie-Ashtiani, B., Simmons, C.T. and Barry, D.A. 2013. Seawater intrusion processes, investigation and management: Recent advances and future challenges. Advances in Water Resources 51: 3–26
↑ ^9.0 ^9.1 Post, V.E.A., Eichholz, M. and Brentführer R. 2018. Groundwater management in coastal zones. Bundesanstalt für Geowissenschaften und Rohstoffe (BGR). Hannover, Germany, 107 pp.
↑ Dagan G, Bear J. 1968. Solving the problem of local interface upconing in a coastal aquifer by the method of small perturbations. Journal Hydrological Research 6: 15–44
↑ De Louw, P.G.B., Oude Essink, G.H.P., Stuyfzand, P.J. and Van der Zee, S.E.A.T.M. 2010. Upward groundwater flow in boils as the dominant mechanism of salinization in deep polders, The Netherlands. Journal of Hydrology 394: 494-506
↑ Kotb, T.H.S., Watanabe, T., Ogino, Y. and Tanji, K.K. 2000. Soil salinization in the Nile Delta and related policy issues in Egypt. Agricultural Water Management 43: 239-261
↑ ^13.0 ^13.1 Mechlem, K. 2016. Groundwater Governance: The Role of Legal Frameworks at the Local and National Level—Established Practice and Emerging Trends. Water 2016, 8, 347; doi:10.3390/w8080347
↑ ^14.0 ^14.1 ^14.2 Zuurbier, K. G., Kooiman, J. W., Groen, M. M., Maas, B. and Stuyfzand, P. J. 2014. Enabling successful aquifer storage and recovery (ASR) of freshwater using horizontal directional drilled wells (HDDWs) in coastal aquifers. In: Journal of Hydrologic Engineering 20 (3), B4014003
↑ Khadra, W.M., Stuyfzand, P.J. and Khadra, I.M. 2017. Mitigation of saltwater intrusion by ‘integrated fresh-keeper’ wells combined with high recovery reverse osmosis. Science of The Total Environment 574: 796-805
↑ Johnson, T. 2007. Technical Documents on Groundwater and Groundwater Monitoring Battling Seawater Intrusion in the Central and West Coast Basins. WRD Technical Bulletin 13. http://www.wrd.org/engineering/reports/TB13_Fall07_Seawater_Barriers.pdf
↑ ^17.0 ^17.1 Cite error: Invalid <ref> tag; no text was provided for refs named OE
↑ Pool, M. and Carrera, J. 2010. Dynamics of negative hydraulic barriers to prevent seawater intrusion. Hydrogeology Journal 18: 95–105
↑ Nishigaki, M., Kankam-Yeboah, K. and Komatsu, M. 2004. Underground dam technology in some parts of the world. Journal of Groundwater Hydrology 46: 113-130
↑ Wang, K., Li, B., Yu, Q. and Wang, J. 2012. The construction of underground reservoir and its beneficial effect on resource and environment in Shandong Province Peninsula. In: China Geological Survey – Achievements. http://en.cgs.gov.cn/achievements/201601/t20160112_35475.html
↑ Ishida, S., Tsuchihara, T., Yoshimoto, S. and Imaizumi, M. 2011. Sustainable use of groundwater with underground dams. In: Japan Agricultural Research Quarterly 45: 51-61
↑ De Vos, A., Bruning, B., Van Straten, G., Oosterbaan, R., Rozema, J. and Van Bodegom, P. 2016. Crop salt tolerance. Salt Farm Texel. https://www.salineagricultureworldwide.com/uploads/file_uploads/files/Report_Crop_Salt_Tolerance-Salt_Farm_Texel.pdf
↑ Roy, S.J., Negrao, S. and Tester, M. 2014. Salt resistant crop plants. Current Opinion in Biotechnology 26: 115–124
↑ Herckenrath, D. 2012. Informing groundwater models with near-surface geophysical data. Thesis, Technical University of Denmark
↑ Knight, R. 2001. Ground penetrating radar for environmental applications. Annual Review of Earth and Planetary Sciences 29L 229-255
↑ Huisman, J., Hubbard, S., Redman, J. and Annan, A. 2003. Measuring Soil Water Content with Ground Penetrating Radar: A Review. Vadose Zone Journal 2: 476-491
↑ Legchenko, A., Baltassat, J. M., Beauce, A. and Bernard, J. 2002. Nuclear magnetic resonance as a geophysical tool for hydrogeologists. Journal of Applied Geophysics 50: 21-46
↑ Montgomery, E.L. 1971. Determination of coefficient of storage by use of gravity measurements: Ph.D. dissertation, University of Arizona, Tucson, 144 p
↑ Macaulay, S. and Mullen, I. 2007. Predicting salinity impacts of land-use change: Groundwater modelling with airborne electromagnetics and field data, SE Queensland, Australia, International Journal of Applied Earth Observation and Geoinformation 9: 124-129
↑ Auken, E., Christiansen, A. V., Jacobsen, L. H. and Sorensen, K. I. 2008. A resolution study of buried valleys using laterally constrained inversion of TEM data. Journal of Applied Geophysics 65: 10-20
↑ Dahlin, T., Leroux, V. and Nissen, J. 2002. Measuring techniques in induced polarisation imaging. Journal of Applied Geophysics 50: 279– 298

[1] slearningmedia https://www.pbslearningmedia.org/resource/buac17-35-sci-ess-waterdistribute/saltwater-and-freshwater-distribution-on-earth/

[2] WWAP (United Nations World Water Assessment Programme). 2015. The United Nations World Water Development Report 2015: Water for a Sustainable World. Paris, UNESCO https://unesdoc.unesco.org/ark:/48223/pf0000231823

[JP-3] Jiao, J. and Post, V. 2019. Coastal Hydrogeology. Cambridge University Press.

[4] Syvitski, J. P., Kettner, A. J., Overeem, I., Hutton, E. W., Hannon, M. T., Brakenridge, G. R. and Nicholls R. J. 2009. Sinking deltas due to human activities. Nature Geoscience 2: 681-686

[5] Custodio, E. and Bruggeman, G.A., editors. Groundwater problems in coastal areas: a contribution to the International Hydrological Programme. Studies and reports in hydrology, vol. 45. Paris: UNESCO; 1987

[PEB-6] Post, V.E.A., Eichholz, M. and Brentführer R. 2018. Groundwater management in coastal zones. Bundesanstalt für Geowissenschaften und Rohstoffe (BGR). Hannover, Germany, 107 pp.

[7] Dagan, G. and Bear, J. 1968. Solving the problem of local interface upconing in a coastal aquifer by the method of small perturbations. Journal Hydraulogical Research 6: 15–44

[W-8] Werner, A.D., Bakker, M., Post, V.E.A., Vandenbohede, A., Lu, C., Ataie-Ashtiani, B., Simmons, C.T. and Barry, D.A. 2013. Seawater intrusion processes, investigation and management: Recent advances and future challenges. Advances in Water Resources 51: 3–26

[P-9] 9.0 ^9.1 Post, V.E.A., Eichholz, M. and Brentführer R. 2018. Groundwater management in coastal zones. Bundesanstalt für Geowissenschaften und Rohstoffe (BGR). Hannover, Germany, 107 pp.

[10] Dagan G, Bear J. 1968. Solving the problem of local interface upconing in a coastal aquifer by the method of small perturbations. Journal Hydrological Research 6: 15–44

[11] De Louw, P.G.B., Oude Essink, G.H.P., Stuyfzand, P.J. and Van der Zee, S.E.A.T.M. 2010. Upward groundwater flow in boils as the dominant mechanism of salinization in deep polders, The Netherlands. Journal of Hydrology 394: 494-506

[12] Kotb, T.H.S., Watanabe, T., Ogino, Y. and Tanji, K.K. 2000. Soil salinization in the Nile Delta and related policy issues in Egypt. Agricultural Water Management 43: 239-261

[Me-13] 13.0 ^13.1 Mechlem, K. 2016. Groundwater Governance: The Role of Legal Frameworks at the Local and National Level—Established Practice and Emerging Trends. Water 2016, 8, 347; doi:10.3390/w8080347

[Z-14] 14.0 ^14.1 ^14.2 Zuurbier, K. G., Kooiman, J. W., Groen, M. M., Maas, B. and Stuyfzand, P. J. 2014. Enabling successful aquifer storage and recovery (ASR) of freshwater using horizontal directional drilled wells (HDDWs) in coastal aquifers. In: Journal of Hydrologic Engineering 20 (3), B4014003

[15] Khadra, W.M., Stuyfzand, P.J. and Khadra, I.M. 2017. Mitigation of saltwater intrusion by ‘integrated fresh-keeper’ wells combined with high recovery reverse osmosis. Science of The Total Environment 574: 796-805

[16] Johnson, T. 2007. Technical Documents on Groundwater and Groundwater Monitoring Battling Seawater Intrusion in the Central and West Coast Basins. WRD Technical Bulletin 13. http://www.wrd.org/engineering/reports/TB13_Fall07_Seawater_Barriers.pdf

[OE-17] 17.0 ^17.1 Cite error: Invalid <ref> tag; no text was provided for refs named OE

[18] Pool, M. and Carrera, J. 2010. Dynamics of negative hydraulic barriers to prevent seawater intrusion. Hydrogeology Journal 18: 95–105

[19] Nishigaki, M., Kankam-Yeboah, K. and Komatsu, M. 2004. Underground dam technology in some parts of the world. Journal of Groundwater Hydrology 46: 113-130

[20] Wang, K., Li, B., Yu, Q. and Wang, J. 2012. The construction of underground reservoir and its beneficial effect on resource and environment in Shandong Province Peninsula. In: China Geological Survey – Achievements. http://en.cgs.gov.cn/achievements/201601/t20160112_35475.html

[21] Ishida, S., Tsuchihara, T., Yoshimoto, S. and Imaizumi, M. 2011. Sustainable use of groundwater with underground dams. In: Japan Agricultural Research Quarterly 45: 51-61

[22] De Vos, A., Bruning, B., Van Straten, G., Oosterbaan, R., Rozema, J. and Van Bodegom, P. 2016. Crop salt tolerance. Salt Farm Texel. https://www.salineagricultureworldwide.com/uploads/file_uploads/files/Report_Crop_Salt_Tolerance-Salt_Farm_Texel.pdf

[23] Roy, S.J., Negrao, S. and Tester, M. 2014. Salt resistant crop plants. Current Opinion in Biotechnology 26: 115–124

[24] Herckenrath, D. 2012. Informing groundwater models with near-surface geophysical data. Thesis, Technical University of Denmark

[25] Knight, R. 2001. Ground penetrating radar for environmental applications. Annual Review of Earth and Planetary Sciences 29L 229-255

[26] Huisman, J., Hubbard, S., Redman, J. and Annan, A. 2003. Measuring Soil Water Content with Ground Penetrating Radar: A Review. Vadose Zone Journal 2: 476-491

[27] Legchenko, A., Baltassat, J. M., Beauce, A. and Bernard, J. 2002. Nuclear magnetic resonance as a geophysical tool for hydrogeologists. Journal of Applied Geophysics 50: 21-46

[28] Montgomery, E.L. 1971. Determination of coefficient of storage by use of gravity measurements: Ph.D. dissertation, University of Arizona, Tucson, 144 p

[29] Macaulay, S. and Mullen, I. 2007. Predicting salinity impacts of land-use change: Groundwater modelling with airborne electromagnetics and field data, SE Queensland, Australia, International Journal of Applied Earth Observation and Geoinformation 9: 124-129

[30] Auken, E., Christiansen, A. V., Jacobsen, L. H. and Sorensen, K. I. 2008. A resolution study of buried valleys using laterally constrained inversion of TEM data. Journal of Applied Geophysics 65: 10-20

[31] Dahlin, T., Leroux, V. and Nissen, J. 2002. Measuring techniques in induced polarisation imaging. Journal of Applied Geophysics 50: 279– 298

[1]

[2]

[3]

[4]

[5]

[6]

[7]

[8]

[9]

[10]

[11]

[12]

[13]

[14]

[15]

[16]

[17]

[18]

[19]

[20]

[21]

[22]

[23]

[24]

[25]

[26]

[27]

[28]

[29]

[30]

[31]

@@ Line 1: / Line 1: @@
 '''Groundwater management in low-elevation coastal zones'''
-Groundwater management is a major issue in many low-lying coastal areas. This article focuses on shallow coastal [[aquifer]]s connected to the sea.
+Groundwater is an important resource for drinking water and irrigation. However, groundwater extraction in low-lying coastal zones is highly problematic. It raises the salinity of the groundwater and it makes the land sink. Therefore, groundwater management is a major issue in many low-lying coastal areas. This article focuses on shallow coastal [[aquifer]]s connected to the sea.
-==Development in low-lying coastal plains==
-The topography of low-lying coasts generally consists of a coastal barrier (dune, protruding rock, elevated deposit) backed by a coastal plain with elevation close to the sea level: a wetland, a (partly) reclaimed lagoon or a sabkha. The coastal plain constitutes a low-energy environment where fine sediments (clay, silt) were deposited during the past millennia. Abundant plant remains have formed peat layers in coastal plains situated in humid climate zones. Low-lying coastal plains are therefore usually characterized by a poorly permeable upper soil layer from a few meters to several tens of meters thick. This upper soil layer has a low load-bearing capacity.
+==Threats of groundwater extraction==
-Many large coastal cities have expanded into these low plains in recent decades, see [[Testpage2|Coastal cities and sea level rise]]. Non-urbanized parts of the coastal plain mainly serve as agricultural land.
+[[Image:WorldWaterDistribution.png|thumb|300px|left|Fig. 1. World water distribution. Source: pbslearningmedia <ref>pbslearningmedia https://www.pbslearningmedia.org/resource/buac17-35-sci-ess-waterdistribute/saltwater-and-freshwater-distribution-on-earth/</ref>.]]
-The demand for freshwater has increased sharply due to the strong population growth in coastal areas. At the same time, the water supply from the hinterland has decreased due to an increased water demand in the upstream catchment areas. Water scarcity is therefore an urgent problem in many coastal areas. The highest water demand is generally related to irrigation needs. To meet this water demand, groundwater is pumped up in quantities that are larger than the replenishment of the groundwater layer. The following sections describe what the impacts are, how they come about and what measures can be taken.
+[[Image:GroundwaterExtractionTrends.jpg|thumb|250px|right|Fig. 2. Agricultural groundwater usage for selected countries in <math>\small 10^9 \, km^3/year</math>. Source: UN World Water Development Report, 2015<ref> WWAP (United Nations World Water Assessment Programme). 2015. The United Nations World Water Development Report 2015: Water for a Sustainable World. Paris, UNESCO  https://unesdoc.unesco.org/ark:/48223/pf0000231823</ref>.]]
-==Impact of groundwater extraction==
+Fresh water represents only a small fraction of earth's water resource – less than 1%, ice excluded (Fig. 1). Groundwater is by far the most important fresh water resource available for human use. More than 50% of world’s population lives in coastal areas and is largely dependent on fresh groundwater resources for domestic, agricultural and industrial purposes. The exploitation of fresh groundwater resources is sharply increasing as a consequence of population growth, economic growth, intensified agricultural development, and the degradation of surface water resources due to contamination (Fig. 2).
-The massive extraction of groundwater in many coastal areas without sufficient recharge has serious consequences:
+Worldwide, many large coastal cities have expanded into low coastal plains during the past decades, especially in Asia and Africa (see [[Testpage2|Coastal cities and sea level rise]]). Most of these plains emerged after the Holocene marine transgression, when the seabed was raised above sea level by sedimentation behind a sheltering coastal barrier. These deposits form a top soil layer of a few meters up to several tens of meters thick, and contain a high fraction of fine sediments of fluvial and marine origin (and peat, in humid climatic zones). On these poorly draining soils, which are highly susceptible to compaction, extensive urban and industrial development has taken place<ref name=JP> Jiao, J. and Post, V. 2019. Coastal Hydrogeology. Cambridge University Press. </ref>. The land elevation is generally close to the mean high sea level. However, in many areas it is lower and still subsiding, mainly as a result of drainage and groundwater extraction<ref>Syvitski, J. P., Kettner, A. J., Overeem, I., Hutton, E. W., Hannon, M. T., Brakenridge, G. R. and Nicholls R. J.  2009. Sinking deltas due to human activities. Nature Geoscience 2: 681-686</ref>.
-* Increasing seawater intrusion into the subsurface groundwater. This can remain unnoticed for many years because groundwater flow is a slow process. In the long run, however, the groundwater will become saline and unfit for crop irrigation. Evapotranspiration of irrigation water can cause a further increase of the soil salinity and the groundwater. Saline groundwater degrades the foundations of buildings by attacking bricks, concrete and the steel reinforcement.
-* Soil subsidence by compaction when water is extracted from underlying clay or peat layers. In urbanized areas, this compaction is exacerbated by the weight of buildings. The upper boundary of the seawater wedge in the subsurface therefore rises. Crops die when the roots are in contact with salt water and ecosystems are degraded. Moreover, the risk of flooding from the sea increases. It is estimated that worldwide about half a billion people live in subsiding delta areas<ref>Syvitski, J. P., Kettner, A. J., Overeem, I., Hutton, E. W., Hannon, M. T., Brakenridge, G. R. and Nicholls R. J.  2009. Sinking deltas due to human activities. Nature Geoscience 2: 681-686</ref>.
-Soil salinization is not only a problem in coastal areas. IPBES (2018) <ref>IPBES 2018. The IPBES assessment report on land degradation and restoration. Intergovernmental Science-Policy Platform on Biodiversity and Ecosystem Services</ref> estimates that worldwide around 76 million hectares of mostly irrigated land has been permanently lost by salinization and can no longer be farmed, with a further 60 million hectares damaged. Coastal areas are particularly vulnerable because of intensive groundwater use and associated increased seawater intrusion. This vulnerability is exacerbated by the effects of climate change; soil salinization is increased by a higher relative sea level, increase of evapotranspiration, more frequent droughts and declining river runoff to the coast.
+Intensive groundwater extraction from underlying water-bearing layers (aquifers) stimulates the intrusion of seawater, leading to increased groundwater salinity<ref>Custodio, E. and Bruggeman, G.A., editors. Groundwater problems in coastal areas: a contribution to the International Hydrological Programme. Studies and reports in hydrology, vol. 45. Paris: UNESCO; 1987</ref>. In the lowest areas, brackish groundwater may reach the surface by upward groundwater flow through the confining top layer, so-called 'saline seepage'.
+The threats of uncontrolled groundwater extraction can remain unnoticed for many years because groundwater flow is a slow process. However, in the long run they are considerable <ref name=PEB>Post, V.E.A., Eichholz, M. and Brentführer R. 2018. Groundwater management in coastal zones. Bundesanstalt für Geowissenschaften und Rohstoffe (BGR). Hannover, Germany, 107 pp.</ref>:
+* unsuitability of groundwater for drinking water,
+* reduced usability of groundwater for irrigation,
+* soil salinization detrimental to crop growth,
+* deterioration of the foundation of buildings by corrosion of concrete, reinforcement and bricks,
+* soil subsidence and increased vulnerability to flooding,
+* danger of collapse of buildings due to soil instability.
+In addition, the anticipated sea level rise and the decrease of recharge, due to climate change and increased water demand in the upstream catchment areas, will further exacerbate the pressures on coastal groundwater systems.
 ==Salt intrusion processes==
-Seawater intrudes into the underground of the coastal plain through [[aquifer]]s, permeable soil layers consisting of medium / coarse granular material or porous / fissured rock. It pushes fresh water higher inland due to its greater density. A counter-pressure is exerted by the fresh water table in the unsaturated inland zone situated above sea level. Due to the small density difference, a small elevation of the fresh water head is sufficient to keep the seawater intrusion in balance. An increase in the freshwater head of 1 m pushes the seawater wedge into the subsoil about 40 m downwards. The equilibrium situation is shown schematically in Fig. 1. In this figure it is assumed that the permeability of the underground is the same everywhere. In reality, however, this is never the case due to the presence of poorly permeable layers ([[aquitard]]s); Fig. 2 shows a still much simplified but slightly more realistic image.
+[[Image:BalanceSaltFresh.jpg|thumb|left|250px|Fig. 3. A small level difference is sufficient to keep a large fresh water column in balance with a salt water column.]]
+Seawater intrudes into the underground of the coastal plain through [[aquifer]]s, permeable soil layers consisting of medium / coarse granular material or porous / fissured rock. Due to its greater density, it enters like a wedge that pushes fresh water inshore, see Fig. 4. A counter-pressure is exerted by the inshore rising fresh water table. Due to the small density difference, a small elevation of the fresh water head is sufficient to keep the seawater intrusion in balance, see Fig. 3. In Fig. 4 it is assumed that the permeability of the underground is the same everywhere. In reality, however, this is never the case due to the presence of poorly permeable layers ([[aquitard]]s); Fig. 5 shows a still much simplified but slightly more realistic image. A rough estimate of the intrusion length <math>L</math> of the seawater wedge into a confined aquifer is given by <ref>Dagan, G. and Bear, J. 1968. Solving the problem of local interface upconing in a coastal aquifer by the method
+of small perturbations. Journal Hydraulogical Research 6: 15–44</ref>
+<math>L \approx \alpha k D^2 / (2 Q) ,  \qquad (1)</math>
+where <math>\alpha \approx  1/40</math> is the relative density difference, <math>k</math> is the hydraulic conductivity, <math>D</math> is the aquifer depth and <math>Q</math> is the groundwater discharge.
@@ Line 29: / Line 41: @@
 |-
 | valign="top"|
-[[File:SeawaterIntrusionScheme1.jpg|thumb|left|450px|Fig. 1. Schematic representation of seawater intrusion into a homogeneous coastal aquifer.]]
+[[File:SeawaterIntrusion1.jpg|thumb|left|450px|Fig. 4. Schematic representation of seawater intrusion into a homogeneous coastal aquifer.]]
 | valign="top"|
-[[File:SeawaterIntrusionScheme2.jpg|thumb|left|450px| Fig. 2. Schematic representation of seawater intrusion into a coastal aquifer with confining top layer.]]
+[[File:SeawaterIntrusion2.jpg|thumb|left|450px| Fig. 5. Schematic representation of seawater intrusion into a multi-aquifer system.]]
 |}
+Seawater intrusion depends, via the groundwater discharge <math>Q</math>, on the elevation difference between the inland fresh water table and the water level at sea. The sea level is variable due to tidal motion and wind set-up / set-down and the inland fresh water table varies over the seasons in response to variable fresh water runoff, evapotranspiration and extractions. These fluctuations in the groundwater pressure gradient, together with spatial inhomogeneities in the geologic structure, contribute to mixing across the fresh-salt interface <ref name=W>Werner, A.D., Bakker, M., Post, V.E.A., Vandenbohede, A., Lu, C., Ataie-Ashtiani, B., Simmons, C.T. and Barry, D.A. 2013. Seawater intrusion processes, investigation and management: Recent advances and future challenges. Advances in Water Resources 51: 3–26</ref>. Sea level rise is an ongoing trend that gradually increases the seawater intrusion into the underground. Shoreline retreat associated with sea level rise can also play a role. Seawater intrusion is further enhanced in case of a trend-wise decrease of the fresh groundwater flux to the coast.
-Seawater intrusion depends on the elevation difference between the inland fresh water table and the water level at sea. The sea level is variable due to tidal motion and wind set-up / set-down and the inland fresh water table varies over the seasons in response to variable fresh water runoff, evapotranspiration and extractions. These fluctuations in the groundwater pressure gradient contribute to mixing across the fresh-salt interface (REF?). Sea level rise is an ongoing trend that gradually increases the seawater intrusion into the underground. Shoreline retreat associated with sea level rise can also play a role. Seawater intrusion is further enhanced in case of a trend-wise decrease of the fresh groundwater flux to the coast and increasing abstraction of groundwater without equivalent fresh water recharge.
+Several other processes contribute to salinization of coastal aquifers.
-In some cases, the coastal barrier cannot prevent flooding of the coastal plain from the sea under extreme circumstances. The flooding seawater infiltrates in this case from the surface into the groundwater, which therefore becomes saline and unsuitable for use. Because the diffusion of seawater into the groundwater is a slow process, increased salinity levels are maintained for a long time <ref name=P>Post, V.E.A., Eichholz, M. and Brentführer R. 2018. Groundwater management in coastal zones. Bundesanstalt für Geowissenschaften und Rohstoffe (BGR). Hannover, Germany, 107 pp.</ref>.
+* Marine transgression.
+Many coastal areas were flooded by the sea during the Holocene transgression, before sedimentation raised the seafloor above mean high water level and before fluvial processes became dominant.  The present saline groundwater was largely formed during this period. Saline intrusion in coastal aquifers by marine transgression occurs today only under extreme storms. Such extreme conditions are rare, but they are expected to become much more frequent in future as a consequence of relative sea level rise (see [[Sea level rise]]). The process of seawater infiltration in a fresh aquifer resulting from a marine flood is shown in Fig. 6. Increased groundwater salinities persist several years after such flood events<ref name=P>Post, V.E.A., Eichholz, M. and Brentführer R. 2018. Groundwater management in coastal zones. Bundesanstalt für Geowissenschaften und Rohstoffe (BGR). Hannover, Germany, 107 pp.</ref>.
-When no fresh water is present in the subsurface layer, as is often the case in arid coastal plains, crops must be irrigated with water that is supplied from elsewhere. Due to water scarcity, the infiltrated irrigation water is collected in special drains and re-used for irrigation. Such an irrigation system exists, for example, in the Nile Delta <ref> Kotb, T.H.S., Watanabe, T., Ogino, Y. and Tanji, K.K. 2000. Soil salinization in the Nile Delta and related policy issues in Egypt. Agricultural Water Management 43: 239-261 </ref>. Because the irrigation water is mixed with brackish groundwater, re-use causes, in combination with evapotranspiration, a net salt flux to the land surface.
-Groundwater flows very slowly, often no more than a few meters per year or even less. The flow rate depends linearly on the product of pressure gradient and permeability. The permeability, often expressed as [https://en.wikipedia.org/wiki/Hydraulic_conductivity hydraulic conductivity], is usually very low. This means that the effect of groundwater extraction or infiltration is initially localized and will only be felt at greater distance after a long period. It also means that large pressure gradients can occur, associated with a steep slope of the salt-fresh interface. When pumping up groundwater, salt groundwater can therefore easily rise from great depths, see Fig. 3. This effect is termed 'upconing'. The same happens when groundwater seeps through a passage in a confining upper layer, as shown in Fig.4. Such passages - discontinuities or cracks in the upper layer or man-made pits - are called 'boils'.
+* Seawater intrusion via estuaries.
+Coastal aquifers are not only in contact with salt water at the land-sea boundary but often also with salt water of estuaries. In this way, intrusion of saline surface water into shallow groundwater can take place further inland (Fig. 7). The intrusion of seawater in estuaries is discussed in the articles [[Seawater intrusion and mixing in estuaries]] and [[Estuarine circulation]]. Seawater intrusion in estuaries has strongly increased during the past century due to channel deepening (dredging) for navigational purposes. The greatest incursion of high salinity seawater occurs in periods of low fluvial runoff, especially in microtidal estuaries (see [[Salt wedge estuaries]]).
 {| border="0"
 |-
 | valign="top"|
-[[File:AbstractionUpconing.jpg|thumb|left|450px|Fig. 3. Salt water upconing under an abstraction well.]]
+[[File:MarineTransgression.jpg|thumb|left|400px|Fig. 6. Infiltration of marine flood water into the underground.]]
 | valign="top"|
-[[File:SeepageUpconing.jpg|thumb|left|250px| Fig. 4. Boil: Salt water upconing under a seepage hotspot.]]
+[[File:EstuaryIntrusion.jpg|thumb|left|400px|Fig. 7. Intrusion of seawater from a salt-wedge estuary into the underground.]]
 |}
+* Groundwater extraction.
+Intensive groundwater extraction increases the intrusion of seawater into the coastal aquifer by diminishing the groundwater discharge to the sea (according to Eq. 1). This intrusion is a slow process, but with a long-lasting impact. The most immediate effect of pumping up groundwater is the rise of the fresh-salt transition under the well, a phenomenon called 'upconing', see Fig. 8. When a critical limit of the extraction rate is exceeded, the fresh-salt transition rises up to the well mouth and the pumped water becomes brackish. The rise of the fresh-salt transition is strongest in cases where the hydraulic conductivity <math>k</math> of the aquifer is small (low conductivity limits the horizontal groundwater flow towards the well)<ref> Dagan G, Bear J. 1968. Solving the problem of local interface upconing in a coastal aquifer by the method of small perturbations. Journal Hydrological Research 6: 15–44</ref>. For aquifers with a low permeability (small <math>k</math>), only small abstraction rates are possible.
-In coastal plains lying below sea level, saline intrusion into the upper soil layer is a major issue, even in countries with rainfall excess. Saline water can rise to the surface by different processes (see Fig. 5): (1) diffuse seepage of saline groundwater in case of a semipermeable upper layer; (2) preferential saline seepage through sandy paleochannel belts in the confining layer and (3) intense seepage via localised boils in waterways or on the land (De Louw et al., 2010<ref>De Louw, P.G.B., Oude Essink, G.H.P., Stuyfzand, P.J. and Van der Zee, S.E.A.T.M. 2010. Upward groundwater flow in boils as the dominant mechanism of salinization in deep polders, The Netherlands. Journal of Hydrology 394: 494-506</ref>). The highest concentration of saline groundwater is found at boils through which groundwater preferentially discharges at high velocities, thereby resulting in upconing of deeper and more saline groundwater. In many deep polders, the salinity of the surface water system is therefore largely determined by these saline boils (De Louw, 2013 <ref>De Louw, P.G.B.  2013. Preferential seepage via boils and interactions between shallow rainwater lenses and saline seepage. Thesis, Vrije Universiteit Amsterdam</ref>). Where rainwater or fresh surface water supplies are limited, saline seepage leads to salinization of surface water and shallow groundwater - a process known as internal salinization.
+* Saline seepage.
+In areas situated below sea level, groundwater can move upwards to the soil surface if the upper soil layer is semipermeable, see Fig. 9 and 10. The upward moving saline seepage water may (1) discharge directly in lakes, canals, ditches or subsurface drain tiles leading to the salinization of surface waters, (2) mix near the surface with shallow fresh groundwater, or even (3) reach the root zone affecting crop growth and natural vegetation. Where rainwater or fresh surface water supplies are limited, saline seepage leads to salinization of surface water and shallow groundwater - a process known as internal salinization. The seepage flow depends on the surface soil level and on the thickness and permeability of the top soil layer. Seepage flow is enhanced at places where ancient sandy deposits are close to the surface or where cracks exist in the top clay layer, giving rise to so-called 'boils' <ref>De Louw, P.G.B., Oude Essink, G.H.P., Stuyfzand, P.J. and Van der Zee, S.E.A.T.M. 2010. Upward groundwater flow in boils as the dominant mechanism of salinization in deep polders, The Netherlands. Journal of Hydrology 394: 494-506</ref>. Seepage in deep polders is increased when the top soil is drained for agricultural purposes; compaction of clay and peat soils is another serious consequence of drainage. The effect of seepage on seawater intrusion is similar to the effect of groundwater extraction; it causes upconing of brackish groundwater and increases the intrusion of seawater into the coastal aquifer.
+{| border="0"
+|-
+| valign="top"|
+[[File:UpconingWell.jpg|thumb|left|200px|Fig. 8. Upconing brackish water under a pumping well.]]
+| valign="top"|
+[[File:PolderSeepage.jpg|thumb|left|250px|Fig. 9. Groundwater seepage into a polder and associated rise of the salt-fresh interface.]]
+| valign="top"|
+[[File:PolderDrainage.jpg|thumb|left|250px|Fig. 10. Drainage of a polder causing upconing of brackish water into the ditches.  ]]
+|}
- [[Image:SeepageMechanisms.jpg|thumb|600px|center|Fig. 5. Illustration of different seepage processes.]]
+* Irrigation practices.
+In arid coastal plains where the groundwater salinity is too high, crops must be irrigated with water that is supplied from elsewhere. Due to water scarcity, the infiltrated irrigation water is collected in special drains and re-used for irrigation. Such an irrigation system exists, for example, in the Nile Delta <ref> Kotb, T.H.S., Watanabe, T., Ogino, Y. and Tanji, K.K. 2000. Soil salinization in the Nile Delta and related policy issues in Egypt. Agricultural Water Management 43: 239-261 </ref>. Because the irrigation water is mixed with brackish groundwater, re-use can cause, in combination with evapotranspiration, a net salt flux to the land surface.
 ==Groundwater management==
+ [[Image:GroundwaterManagementAspects.jpg|thumb|400px|left|Fig. 11. Factors that influence the groundwater system. From Post (2018)<ref name=P></ref>.]]
- [[Image:GroundwaterManagementAspects.jpg|thumb|400px|left|Fig. 6. Factors that influence the groundwater system. From Post (2018)<ref name=P></ref>.]]
+Groundwater management requires an integrated approach based on insight into the multiple factors that influence the groundwater system, see Fig. 11. This insight is usually fragmentary due to the complexity of the groundwater system. Groundwater flow models are crucial for estimating the influence of abstractions on the groundwater status, see section [[#Groundwater modelling and observation|Groundwater modelling]]. Permits, metering of wells, quotas and water taxes are the legal instruments on which sustainable groundwater management can be based, together with obligations of monitoring and reporting. Polluting substances from point sources (industrial effluents, household sewage) and from diffuse sources (agricultural effluents containing pesticides, herbicides, fertilizers) are a major danger for groundwater contamination. Adequate environmental policy, agricultural policy, and spatial policy that tackle the pollution issue are prerequisite for sustainable groundwater management. The effectiveness of groundwater management can be increased by involving local stakeholders, due to the strong link between use and usability of the groundwater resource. Understanding and support from stakeholders makes it easier to enforce legal rules and provisions. Without support of stakeholders, enforcement is usually difficult to achieve <ref name=Me>Mechlem, K. 2016. Groundwater Governance: The Role of Legal Frameworks at the Local and National Level—Established Practice and Emerging Trends. Water 2016, 8, 347; doi:10.3390/w8080347</ref>.
-Groundwater management requires an integrated approach based on insight into the multiple factors that influence the groundwater system, see Fig. 6. This insight is usually fragmentary due to the complexity of the groundwater system. The minimum required knowledge consists of an inventory of all existing wells, the quantity and quality of the abstracted water and its destination. From the analysis of these data, complemented with hydrogeological data of groundwater recharge and data of evapotranspiration, the influence of abstractions on the groundwater status can be estimated. Permits, metering of wells, quotas and water taxes are the legal instruments on which sustainable groundwater management can be based, together with obligations of monitoring and reporting. Polluting substances from point sources (industrial effluents, household sewage) and from diffuse sources (agricultural effluents containing pesticides, herbicides, fertilizers) are a major danger for groundwater contamination. Adequate environmental policy, agricultural policy, and spatial policy that tackle the pollution issue are prerequisite for sustainable groundwater management. The effectiveness of groundwater management can be increased by involving local stakeholders, due to the strong link between use and usability of the groundwater resource. Understanding and support from stakeholders makes it easier to enforce legal rules and provisions. Without support of stakeholders, enforcement is usually difficult to achieve <ref name=Me>Mechlem, K. 2016. Groundwater Governance: The Role of Legal Frameworks at the Local and National Level—Established Practice and Emerging Trends. Water 2016, 8, 347; doi:10.3390/w8080347</ref>.
+Monitoring aquifers for protection against depletion and pollution is a technically demanding and costly exercise so that information about aquifers is often incomplete. The costs for setting up a monitoring network, collecting data regularly, processing, interpreting, and storing it in databases, including unified databases at the national level, are one of the reasons why in developed and developing countries alike water rights and monitoring obligations, especially with respect to groundwater, may remain unimplemented <ref name=Me></ref>.
-Monitoring aquifers for protection against depletion and pollution is a technically demanding and costly exercise so that information about aquifers is often incomplete. The costs for setting up a monitoring network, collecting data regularly, processing, interpreting, and storing it in databases, including unified databases at the national level, are one of the reasons why in developed and developing countries alike water rights and monitoring obligations, especially with respect to groundwater, may remain unimplemented <ref name=Me></ref>.
+==Measures to reduce soil and groundwater salinization==
+Different types of measures are possible to reduce soil and groundwater salinization, which can be applied depending on the geological setting and the causes of salt intrusion.
-==Measures to combat salt intrusion==
+. Horizontal wells.
-Different types of measures are possible to combat salt intrusion, which can be applied depending on the geological setting and the causes of salt intrusion.
+The risk of upconing of the salt-fresh interface can be reduced by 'skimming' the fresh water lens with a horizontal well, see Fig. 12. With this measure it is possible to exploit a brackish aquifer with a relatively thin fresh water lens. Periodically, natural (or artificial) recharge of the fresh water lens is necessary to get the salt-fresh interface back to its former position.
-. If sufficient fresh water is available, thanks to excess precipitation or river supply, salt water can be flushed back to the sea. The intrusion of seawater into rivers will be counteracted if the river discharge is sufficiently high. The effectiveness of river flushing depends on the bathymetric characteristics of the estuary, as discussed in [[Seawater intrusion and mixing in estuaries]]. Salinization of shallow groundwater in the coastal plain can be prevented by installing drainage channels (ditches) that are flushed with rainwater or with water that is supplied from nearby rivers. Groundwater abstraction in periods of drought must be compensated by equivalent fresh water recharge during wet periods, by precipitation or by fresh water supply from elsewhere. This allows a fresh (rain)water lens to be maintained in the upper groundwater layer.
+. Fresh water storage by infiltration.
-. If the freshwater availability for the above measures is insufficient, other interventions to counteract seawater intrusion can be considered, depending on the structure of the substrate. If fresh water is available during sufficiently long and frequent periods, a hydraulic barrier can be created in the upper aquifer. The hydraulic barrier consists of a freshwater injection system that repels seawater from the upper aquifer to the sea. Further inland,  freshwater can be extracted (to a limited extent) in periods of drought from the fresh aquifer, see Fig. 7. A practical example is the hydraulic barrier installed in California near Los Angeles <ref>Johnson, T. 2007. Technical Documents on Groundwater and Groundwater Monitoring Battling Seawater Intrusion in the Central and West Coast Basins. WRD Technical Bulletin 13. http://www.wrd.org/engineering/reports/TB13_Fall07_Seawater_Barriers.pdf</ref>. Another possibility is the creation of a physical barrier in the upper aquifer near the sea boundary, e.g. by injecting concrete, see Fig. 8. Such interventions have been implemented in Shandong province on the Bohai Sea in China <ref>Ishida, S., Tsuchihara, T., Yoshimoto, S. and Imaizumi, M. 2011. Sustainable use of groundwater with underground dams. In: Japan Agricultural Research Quarterly 45: 51-61</ref>.
+According to the principle shown in Fig. 3, a large fresh water reservoir can be created in the subsoil by raising the fresh water table. This principle can be applied in coastal zones protected by a dune belt. By infiltrating fresh water in the dunes – rain water or fresh water from other sources – the fresh water table can be raised such that a large column of fresh water in the subsoil is kept in hydrostatic balance with the seawater, due to the different densities (Fig. 13). If present, any protruding thick sandy deposit in the coastal zone (e.g., relic channel bars) can serve for fresh water storage in a similar way. Dune infiltration is widely used in the Netherlands to provide drinking water to coastal cities (e.g., Amsterdam, The Hague).
 {| border="0"
 |-
 | valign="top"|
-[[File:HydraulicBarrier.jpg|thumb|left|450px|Fig. 7. Schematic representation of a hydraulic barrier at the seaward entrance of an aquifer. The marine salt wedge is expelled in periods of abundant fresh water. Inland abstraction wells are exploited in periods of drought.]]
+[[File:SkimmingWell.jpg|thumb|250px|left|Fig. 12. Horizontal skimming well. The upconing effect is limited by spreading the extraction over a broad zone.]]
 | valign="top"|
-[[File:PhysicalBarrier.jpg|thumb|left|450px|Fig. 8. Schematic representation of a physical barrier at the seaward entrance of an aquifer.]]
+[[File:DuneInfiltration.jpg|thumb|250px|left|Fig. 13. Large fresh water reservoir created by dune infiltration.]]
 |}
+. Fresh water storage by injection.
-. Areas subject to strong salt seepage can be isolated by adjusting the intake, discharge, storage and drainage systems. This requires identifying the saline area and building a bypass around it to isolate the saline area and prevent it from being used during dry periods. This system can be further optimized through dynamic operational management of drainage, fresh water intake, and temporary storage of saline seepage water based on weather forecasts and real-time monitoring of salt concentrations at strategic locations in the polder <ref>Kamps, P., Nienhuis, P., van den Heuvel, D. and de Joode, H. 2016. Monitoring Well Optimization for Surveying the Fresh/Saline Groundwater Interface in the Amsterdam Water Supply Dunes. 24th Salt Water Intrusion Meeting and the 4th Asia-Pacific Coastal Aquifer Management Meeting, July 2016, Cairns, Australia</ref>. Automatic weirs can easily control the temporary isolation during dry periods of saline areas with a significant number of boils. The temporarily stored salt water can then be discharged during rainstorm events when salt concentrations are low.
+Collected rainwater – or fresh water from other sources – can temporarily be stored in the subsoil for later re-use. Fresh water is injected into the deeper part of the aquifer and collected later from a higher pumping well, as shown in Fig. 14. A larger volume of fresh water can be stored by lowering the salt-fresh interface. Salt groundwater is pumped away from greater depth to reduce the hydrostatic pressure on the surface layer. This will prevent an existing freshwater lens from being pushed out<ref name=Z> Zuurbier, K. G., Kooiman, J. W., Groen, M. M., Maas, B. and Stuyfzand, P. J.  2014. Enabling successful aquifer storage and recovery (ASR) of freshwater using horizontal directional drilled wells (HDDWs) in coastal aquifers. In: Journal of Hydrologic Engineering 20 (3), B4014003</ref>. The brackish/salt water has to be discharged to the sea or it can be treated in a desalination plant for re-use<ref>Khadra, W.M., Stuyfzand, P.J. and Khadra, I.M. 2017. Mitigation of saltwater intrusion by ‘integrated fresh-keeper’ wells combined with high recovery reverse osmosis. Science of The Total Environment 574: 796-805</ref>. The extraction-injection is adjusted by a so-called automatic 'freshmaker system'<ref name=Z></ref>. The principle is shown schematically in Fig. 15. Another option (if technically and economically feasible) is to pump the brackish/salt water through the underlying aquitard to a lower aquifer ('freshkeeper system'<ref name=Z></ref>), see Fig. 16.
+{| border="0"
+|-
+| valign="top"|
+[[File: TemporaryStorage.jpg|thumb|left|300px|Fig. 14. Temporary storage of rainwater. ]]
+| valign="top"|
+[[File:Freshmaker.jpg|thumb|left|250px|Fig. 15. Principle of the freshmaker system: withdrawal of brackish groundwater to make room for a thick fresh water lens. ]]
+| valign="top"|
+[[File:Freshkeeper.jpg|thumb|left|200px|Fig. 16. Principle of the freshkeeper system: removal of brackish groundwater to a lower aquifer to make room for storage of fresh water.  ]]
+|}
-Field research has shown that sealing naturally occurring boils (which arise from the heaving and cracking of the confining layer) is very difficult and cannot be achieved with current technologies <ref>De Louw, P.G.B., Doornenbal, P. and Hendriks, D.M.D. 2012. Field research on boil sealing. Deltares-report 1201949-000, 52pp. [in Dutch]</ref>. This is because in general a relatively large area (about 20 by 20 metres on average) is affected by the heaving and cracking of the confining layer, rendering the area unstable and riddled with cracks. Boil sealing fairly quickly leads to development of new boils in existing cracks in the unstable boil area. Boil sealing has proved to be much simpler and more promising for boils which arise from the removal of structures, such as level filters or sheet piles, or from the sealing of old gas wells. This can be achieved in two ways: through injection of expanding and persisting fluids or through biosealing. If expanding and persisting gels are used, it is advised to use an environmentally friendly gel. Biosealing is by definition environmentally friendly.
+. Aquifer barriers to prevent seawater intrusion.
-. Creation of fresh water reservoirs below elevated sandy deposits. In low-lying coastal areas, sandy deposits are often present, such as a dune belt along the coast, but also sand deposits in paleochannels that rise above the mean ground level. A large underground freshwater reservoir can be created by infiltrating fresh water into these sand deposits. The explanation for this is the small difference in density between freshwater and seawater, which, however, is large enough to prevent the mixing of freshwater and seawater. As a result, a large column of fresh water can be in hydrostatic equilibrium with surrounding seawater. An example of freshwater infiltration in a dune area is shown schematically in Fig. 9. The use of freshwater infiltration in a paleochannel deposit protruding above land is shown schematically in Fig. 10.
+Two types of barriers have been implemented in practice: hydraulic barriers and physical barriers. The usual principle of a hydraulic barrier is shown in Fig. 17. Fresh water (for example, purified sewage water) is injected into the aquifer close to the seaward boundary to create a pressure head that prevents the intrusion of seawater. Further inland,  freshwater can be extracted (to a limited extent) in periods of drought from the fresh aquifer. A practical example is the hydraulic barrier installed in California near Los Angeles <ref>Johnson, T. 2007. Technical Documents on Groundwater and Groundwater Monitoring Battling Seawater Intrusion in the Central and West Coast Basins. WRD Technical Bulletin 13. http://www.wrd.org/engineering/reports/TB13_Fall07_Seawater_Barriers.pdf</ref>. The effectiveness of this solution depends on the availability of fresh water during sufficiently long and frequent periods. Another principle is based on extraction of intruding seawater, as shown in Fig. 18. Drawbacks of this principle are the disposal of the extracted saline or brackish groundwater and the lowering of the piezometric heads, especially in shallow coastal aquifers<ref name=OE></ref>. This latter issue can be mitigated by fresh water injection further landward<ref>Pool, M. and Carrera, J. 2010. Dynamics of negative hydraulic barriers to prevent seawater intrusion. Hydrogeology Journal 18: 95–105</ref>.
+Physical subsurface barriers have been constructed in several countries, especially in Japan<ref> Nishigaki, M., Kankam-Yeboah, K. and Komatsu, M. 2004. Underground dam technology in some parts of the world. Journal of Groundwater Hydrology 46: 113-130</ref> and China <ref> Wang, K., Li, B., Yu, Q. and Wang, J. 2012. The construction of underground reservoir and its beneficial effect on resource and environment in Shandong Province Peninsula. In: China Geological Survey – Achievements. http://en.cgs.gov.cn/achievements/201601/t20160112_35475.html</ref>. The barriers were generally built of concrete using grouting techniques or mixed-in-place slurry-wall methods<ref>Ishida, S., Tsuchihara, T., Yoshimoto, S. and Imaizumi, M. 2011. Sustainable use of groundwater with underground dams. In: Japan Agricultural Research Quarterly 45: 51-61</ref>. The dams serve as a barrier for seawater intrusion, and also create underground fresh water storage in periods of high precipitation (Fig. 19). However, the costs are high and the solution is only applicable in shallow aquifers<ref name=OE></ref>.
 {| border="0"
 |-
 | valign="top"|
-[[File:DuneInfiltration.jpg|thumb|left|300px|Fig. 9. Schematic representation of the underground fresh water reservoir created by fresh water infiltration into the dune belt.]]
+[[File:HydraulicInjectionBarrier.jpg|thumb|left|300px|Fig. 17. Hydraulic injection barrier at the seaward entrance of an aquifer. The marine salt wedge is expelled in periods of abundant fresh water. Inland abstraction wells are exploited in periods of drought.]]
 | valign="top"|
-[[File:PaleochannelInfiltration.jpg|thumb|left|250px|Fig. 10. Schematic representation of the underground fresh water reservoir created by fresh water infiltration into a sandy paleochannel deposit protruding above the mean land level.]]
+[[File:HydraulicAbstractionBarrier.jpg|thumb|left|300px|Fig. 18. Hydraulic abstraction barrier at the seaward entrance of an aquifer. The marine salt wedge is expelled in periods of abundant fresh water. Inland abstraction wells are exploited in periods of drought.]]
 | valign="top"|
-[[File:FreshMakerSystem.jpg|thumb|left|300px|Fig. 11. Creation of a fresh water lens by fresh water infiltration after artificial lowering of the salt water interface.]]
+[[File:PhysicalBarrier.jpg|thumb|left|300px|Fig. 19. Physical subsurface barrier at the seaward entrance of an aquifer.]]
 |}
+. Isolating saline areas.
-. Creation of a fresh water lens by fresh water infiltration and lowering of the brackish groundwater table <ref> Zuurbier, K. G., Kooiman, J. W., Groen, M. M., Maas, B. and Stuyfzand, P. J.  2014. Enabling successful aquifer storage and recovery (ASR) of freshwater using horizontal directional drilled wells (HDDWs) in coastal aquifers. In: Journal of Hydrologic Engineering 20 (3), B4014003</ref>. Salt groundwater is pumped away from greater depth to reduce the hydrostatic pressure on the surface layer. This can prevent an existing freshwater lens from being pushed out. The salty water is discharged into the sea (or a river) via separate drains. A freshwater lens can also be enlarged or created by injecting fresh water supplied from elsewhere. The extraction-injection is operated by a so-called automatic 'freshmaker' system. The principle is shown schematically in Fig. 11.
+Saline seepage due to local boils – a major salinization mechanism in the deep polders in the Netherlands – is combated by building a bypass around the saline areas. Automatic weirs control the temporary isolation (during dry periods) of saline areas with a significant number of boils. The temporarily stored salt water is discharged during rainstorm events when salt concentrations are low. Boils that arise from the removal of structures, such as level filters or sheet piles, or from the sealing of old gas wells, can be sealed. This can be done through injection of expanding and persisting fluids or through biosealing; the latter option is the most environmentally friendly.
 ==Dealing with brackish groundwater==
 In arid coastal zones with endemic freshwater shortages, there are no good options for preventing salt intrusion into the groundwater. Strict regulation of groundwater abstraction is necessary to make land use possible.
-Agriculture has to make use of salt-tolerant crops. Fortunately, ever better crops are being developed for saline conditions, including by genetic modification techniques.
+Agriculture has to make use of salt-tolerant crops. Fortunately, ever better crops are being developed for saline conditions, including by genetic modification techniques<ref>De Vos, A., Bruning, B., Van Straten, G., Oosterbaan, R., Rozema, J. and Van Bodegom, P. 2016. Crop salt tolerance. Salt Farm Texel. https://www.salineagricultureworldwide.com/uploads/file_uploads/files/Report_Crop_Salt_Tolerance-Salt_Farm_Texel.pdf </ref><ref> Roy, S.J., Negrao, S. and Tester, M. 2014. Salt resistant crop plants. Current Opinion in Biotechnology 26: 115–124</ref>. In addition, infrastructure must be protected against corrosion by saline groundwater, including the use of salt-resistant concrete.
-In addition, infrastructure must be protected against corrosion by saline groundwater, including the use of salt-resistant concrete.
-==Groundwater modelling==
-Groundwater flow can be described with [https://en.wikipedia.org/wiki/Darcy%27s_law Darcy's law], which couples the flow rate linearly to the gradient in the hydrostatic groundwater pressure. The crucial problem is the determination of the coupling coefficient, the so-called [https://en.wikipedia.org/wiki/Hydraulic_conductivity hydraulic conductivity]. This coefficient is different for each soil type. The structure and composition of the substrate is generally very complex. It is a reflection of the geological history in which a large number of processes on very diverse space and time scales play a role. The reliability with which groundwater flows can be simulated therefore depends primarily on the extent to which the structure and composition of the subsoil are known. This knowledge usually has large gaps, since sampling the subsurface over great depth requires a great deal of effort and is very expensive. Missing knowledge of the subsurface can be partially overcome by model calibration based on data from wells, piezometric surveys (groundwater pressure) and observations based on geophysical techniques.
+==Groundwater modelling and observation==
+[[Image:AirborneTEM.jpg|thumb|left|250px|Fig. 20. SkyTEM team recording Time Domain Electromagnetic Data. Source: G. Oude Essink, https://publicwiki.deltares.nl/ ]]
+Groundwater flow can be described with [https://en.wikipedia.org/wiki/Darcy%27s_law Darcy's law], which couples the flow rate linearly to the gradient in the hydrostatic groundwater pressure. A crucial problem is the determination of the coupling coefficient, the so-called [https://en.wikipedia.org/wiki/Hydraulic_conductivity hydraulic conductivity]. This coefficient is different for each soil type. The structure and composition of the substrate is generally very complex. It is a reflection of the geological history in which a large number of processes on very diverse space and time scales play a role. The reliability with which groundwater flows can be simulated therefore depends primarily on the extent to which the structure and composition of the subsoil are known. This knowledge usually has large gaps, since sampling the subsurface over great depth requires a great deal of effort and is very expensive. In addition to knowledge of the subsurface structure, knowledge is needed of the distribution of saline water in the underground. Missing knowledge can be partially overcome by model calibration based on data from wells (quantity and quality of abstractions), piezometric surveys (groundwater pressure) and observations based on geophysical techniques.
-In recent decades, a large number of geophysical measurement methods have been developed that indirectly provide information about the structure and properties of the subsurface and groundwater <ref>Herckenrath, D. 2012. Informing groundwater models with near-surface geophysical data. Thesis, Technical University of Denmark</ref>. These are in particular: Seismic techniques, such as Ground Penetrating Radar (GPR <ref>Knight, R. 2001. Ground penetrating radar for environmental applications. Annual Review of Earth and Planetary Sciences 29L 229-255</ref><ref>Huisman, J., Hubbard, S., Redman, J. and Annan, A. 2003. Measuring Soil Water Content with Ground Penetrating Radar: A Review. Vadose Zone Journal 2: 476-491</ref>); Nuclear Magnetic techniques, such as Magnetic Resonance Sounding (MRS <ref>Legchenko, A., Baltassat, J. M., Beauce, A. and Bernard, J. 2002. Nuclear magnetic resonance as a geophysical tool for hydrogeologists. Journal of Applied Geophysics 50: 21-46</ref>), Time Lapse Gravity (TLG <ref> Montgomery, E.L. 1971. Determination of coefficient of storage by use of gravity measurements: Ph.D. dissertation, University of Arizona, Tucson, 144 p</ref>); Electromagnetic techniques <ref>Macaulay, S. and Mullen, I. 2007. Predicting salinity impacts of land-use change: Groundwater modelling with airborne electromagnetics and field data, SE Queensland, Australia, International Journal of Applied Earth Observation and Geoinformation 9: 124-129</ref>, such as Time Domain Electromagnetic sounding (TDEM <ref>Auken, E., Christiansen, A. V., Jacobsen, L. H. and Sorensen, K. I. 2008. A resolution study of buried valleys using laterally constrained inversion of TEM data. Journal of Applied Geophysics 65: 10-20</ref>) and Induced Polarization (IP <ref>Dahlin, T., Leroux, V. and Nissen, J. 2002. Measuring techniques in induced polarisation imaging. Journal of Applied Geophysics 50: 279– 298</ref>). Most of these techniques can be applied on the ground or air-borne. They provide indirect data on, among other things, the structure of the subsurface, the location of the salt-fresh transition, the groundwater flow, and salinity. Together with information from wells, bore holes and model calculations these data enable reasonable estimates of the effect of interventions in the groundwater system. However, the design of groundwater models and the interpretation of model results still require highly specialized knowledge and experience of geohydrological processes.
+In recent decades, a large number of geophysical measurement methods have been developed that indirectly provide information about the structure and properties of the subsurface and groundwater <ref>Herckenrath, D. 2012. Informing groundwater models with near-surface geophysical data. Thesis, Technical University of Denmark</ref>. These are in particular: Seismic techniques, such as Ground Penetrating Radar (GPR <ref>Knight, R. 2001. Ground penetrating radar for environmental applications. Annual Review of Earth and Planetary Sciences 29L 229-255</ref><ref>Huisman, J., Hubbard, S., Redman, J. and Annan, A. 2003. Measuring Soil Water Content with Ground Penetrating Radar: A Review. Vadose Zone Journal 2: 476-491</ref>); Nuclear Magnetic techniques, such as Magnetic Resonance Sounding (MRS <ref>Legchenko, A., Baltassat, J. M., Beauce, A. and Bernard, J. 2002. Nuclear magnetic resonance as a geophysical tool for hydrogeologists. Journal of Applied Geophysics 50: 21-46</ref>), Time Lapse Gravity (TLG <ref> Montgomery, E.L. 1971. Determination of coefficient of storage by use of gravity measurements: Ph.D. dissertation, University of Arizona, Tucson, 144 p</ref>); Electromagnetic techniques <ref>Macaulay, S. and Mullen, I. 2007. Predicting salinity impacts of land-use change: Groundwater modelling with airborne electromagnetics and field data, SE Queensland, Australia, International Journal of Applied Earth Observation and Geoinformation 9: 124-129</ref>, such as Time Domain Electromagnetic sounding (TDEM <ref>Auken, E., Christiansen, A. V., Jacobsen, L. H. and Sorensen, K. I. 2008. A resolution study of buried valleys using laterally constrained inversion of TEM data. Journal of Applied Geophysics 65: 10-20</ref>) and Induced Polarization (IP <ref>Dahlin, T., Leroux, V. and Nissen, J. 2002. Measuring techniques in induced polarisation imaging. Journal of Applied Geophysics 50: 279– 298</ref>). Most of these techniques can be applied on the ground or air-borne (Fig. 20). They provide indirect data on the structure of the subsurface and on the location of the salt-fresh transition, the groundwater flow, and salinity (by making use of the large electrical resistivity contrast between seawater and freshwater). Together with information from wells, bore holes and model calculations these data enable reasonable estimates of the effect of interventions in the groundwater system. However, the design of groundwater models and the interpretation of model results still require highly specialized knowledge and experience of geohydrological processes.
 ==References==
 <references/>

More

Navigation

Tools